Details

---

Model :

• CPM2A-60CDR-D

 

---

Features :
 

• Interrupt Inputs – Triggered when inputs 00003–00006 change OFF → ON; use subroutines 000–003.
• Interval Timer Interrupt – Executes interrupts with 0.1 ms precision; subroutines 000–049 can be assigned.
• Count-up Interrupt – Inputs 00003–00006 count pulses up to 2 kHz; interrupt occurs when count reaches SV.
• Count-check Interrupt – High-speed inputs 00000–00002 count up to 20 kHz or 5 kHz; interrupt occurs when PV = target value or within range.
• Interval Timer (CPM2) – One timer, 0.5 ms – 319,968 ms range, 0.1 ms precision, supports single or scheduled interrupts.
• High-speed Counter – Built-in counter up to 20 kHz; supports target or range comparison independent of PLC cycle time.
• Pulse Outputs – Two outputs supporting single-phase pulses, variable duty pulses, or trapezoidal acceleration/deceleration.
• PV Coordinate System – Can be set to relative or absolute in PLC setup.
• Synchronized Pulse Control – Combines high-speed counter + pulse output to generate pulses 10 Hz – 10 kHz proportional to input frequency.

 

---

Dimension :



 

---

Specifications :
 

Item		CPU Units with 20 I/O points	CPU Units with 30 I/O points	CPU Units with 40 I/O points	CPU Units with 60 I/O points
Supply voltage	AC power	100 to 240 V AC, 50/60 Hz
	DC power	24 VDC
Operating voltage range	AC power	85 to 264 V AC
	DC power	20.4 to 26.4 V DC
Power consumption	AC power	60 VA max.
	DC power	20 W max.
Inrush current	AC power	60 A max.
	DC power	20 A max.
External power supply (AC power supplies only)	Supply voltage	24 VDC
	Output capacity	300 mA
Insulation resistance		20 ΜΩ min. (at 500 V DC) between the external AC terminals and protective earth terminals
Dielectric strength		2,300 V AC 50/60 Hz for 1 min between the external AC and protective earth terminals, leakage current: 10 mA max.
Noise immunity		Conforms to IEC61000-4-4, 2 kV (power lines)
Vibration resistance		10 to 57 Hz, 0.075-mm amplitude, 57 to 150 Hz, acceleration: 9.8 m/s² in X, Y, and Z directions for 80 minutes each (Time coefficient; 8 minutes x coefficient factor 10 = total time 80 minutes)
Shock resistance		147 m/s² three times each in X, Y, and Z directions
Ambient temperature		Operating: 0° to 55°C
		Storage: -20° to 75° C
Humidity		10% to 90% (with no condensation)
Atmosphere		Must be free from corrosive gas
Terminal screw size		M3
Power interrupt time		AC power supply: 10 ms min.
		DC power supply: 2 ms min.
CPU Unit weight	AC power	650 g max.	700 g max.	800 g max.	1,000 g max.
	DC power	550 g max.	600 g max.	700 g max.	900 g max.
Expansion Unit weight		Units with 20 I/O Points : 300 g max.
		Units with 8 Output Points : 250 g max.
		Units with 8 Input Points : 200 g max.
		MAD01 Analog I/O Unit : 150 g max.
		MAD11 Analog I/O Unit : 250 g max.
		AD041/DA041 Analog I/O units : 200 g max.
		Temperature Sensor Units : 250 g max.
		CompoBus/S I/O Link Units : 200 g max.
		DeviceNet I/O Link Unit : 200 g max.
		PROFIBUS-DP I/O Link Unit : 150 g max.

 

---